Moorix Marine Systems
Estimate
One team, two names

The engineers who design your anchoring install it too.

Moorix Marine Systems installs screw anchors for fish and mussel farms and marinas, and helical piles for waterfront structures. mussel.pro designs them: both are names of one company, MusselPro Mühendislik Ltd.. The people who read your site and specify the anchors are the people who turn them in and hand you the torque record.

Get a Project EstimateSee the jobs

Engineering

mussel.pro

  • Site read and seabed interpretation
  • Load analysis and anchor specification
  • Environmental documentation for the permit file

Same engineers, from the first site read to the handover

Installation

Moorix Marine Systems

  • Anchors turned in by hydraulic drive from a work vessel
  • Installation torque recorded for every anchor
  • As-built record handed over at the end of the job

A few of our 500+ anchors, in photographs

We have 15+ years in aquaculture, farming and anchoring, and have put in 500+ anchors. Here are some we have photographs and figures for and can publish. Every figure under a photograph comes from the installation record for that job, and clients are named with their agreement.

Misya Seafood’s blue work vessel, with a crane on its deck, on calm water in a bay, with wind turbines along the hills behind.
Misya Seafood’s work vessel · Koyun Island, Balıkesir: the mussel farm where our anchors hold the lines.
  1. Screw anchor on the seabed at the Misya Seafood mussel farm off Koyun Island, its drive head and mooring eye colonised by marine growth eight years after installation.

    Misya Seafood · Koyun Island, Balıkesir

    A shallow anchor at a working mussel farm

    Photographed eight years after it went in, its drive head and mooring eye grown over with marine life and still in service.

    Installed
    2014
    Depth
    15 m
    Photographed
    2022
  2. Screw anchor installed on the seabed at the Misya Seafood mussel farm off Koyun Island, showing the drive head used to turn it and the revolving eye where the mooring rope is tied.

    Misya Seafood · Koyun Island, Balıkesir

    A deep-set anchor at the same farm

    The drive head the rig turns it by, and the revolving eye the mooring rope is tied to, at 35 metres.

    Installed
    2016
    Depth
    35 m
    Anchor length
    4 m
    Helix plate
    600 mm
  3. Crew on a work vessel lowering a hydraulic drive rig to install screw anchors in shallow water off Pınar Hotel, Erdek.

    Pınar Hotel · Erdek, Balıkesir, Türkiye

    Floating-dock and boat-mooring anchors

    Fourteen anchors for a floating-dock system and four more in deeper water for boat moorings, turned into loose sand from a work vessel. The hotel put the docks off; the boat moorings are in service.

    The full record on the marina page
    Anchors
    18
    Shaft length
    2 m
    Helix diameter
    60 cm
    Safe working load
    4.3 t
    Depth
    2–7 m

Who you will deal with

  • Emre Küçükçolak

    Engineer & Director

    Chemical engineer (BSc, Boğaziçi University) and environmental engineer (M.E., University of Florida), with 15+ years in mussel farming and aquaculture. Designs each mooring under mussel.pro and leads the installation under Moorix. Works in English, German, Spanish, Dutch and Turkish.

Company details

Istanbul, TürkiyeRegistered officeAmsterdam, the NetherlandsSales office
Legal entity
MusselPro Mühendislik Ltd.
Trades as
Moorix Marine Systems (installation) and mussel.pro (engineering design)
Registered office
Istanbul, Türkiye
Sales office
Amsterdam, the Netherlands
Works
Worldwide
Galvanizing
Hot-dip, ASTM A123 / A153
Reply time
An engineer within 24 hours; the full proposal within two business days

Put one team on the whole job.

Send the site: depth, seabed type and loads. An engineer replies within 24 hours with questions and a first read; the full proposal follows within two business days.

Get a Project Estimate